Infineon OptiMOS Type N-Channel MOSFET, 190 mA, 100 V Enhancement, 3-Pin SOT-23

N° de stock RS:: 826-9317
Numéro d'article Distrelec:: 304-44-423
Référence fabricant:: BSS123NH6433XTMA1
Fabricant:: Infineon

Infineon OptiMOS Type N-Channel MOSFET, 190 mA, 100 V Enhancement, 3-Pin SOT-23

Sous-total (1 bobine de 500 unités)*

32,00 €

(TVA exclue)

38,50 €

(TVA incluse)

Frais de livraison offerts pour toute commande de plus de 90,00 €

En stock

6 000 unité(s) prête(s) à être expédiée(s) d'un autre centre de distribution

Besoin de plus? Cliquez sur " Vérifier les dates de livraison " pour plus de détails

Unité	Prix par unité	la bobine*
500 +	0,064 €	32,00 €

*Prix donné à titre indicatif

N° de stock RS:: 826-9317
Numéro d'article Distrelec:: 304-44-423
Référence fabricant:: BSS123NH6433XTMA1
Fabricant:: Infineon

Spécifications

Documentation technique

Législations et de normes

Détails du produit

Recherchez des produits similaires en sélectionnant un ou plusieurs attributs.

Sélectionner tout	Attribut	Valeur
	Marque	Infineon
	Product Type	MOSFET
	Channel Type	Type N
	Maximum Continuous Drain Current Id	190mA
	Maximum Drain Source Voltage Vds	100V
	Series	OptiMOS
	Package Type	SOT-23
	Mount Type	Surface
	Pin Count	3
	Maximum Drain Source Resistance Rds	10Ω
	Channel Mode	Enhancement
	Maximum Power Dissipation Pd	500mW
	Typical Gate Charge Qg @ Vgs	0.6nC
	Minimum Operating Temperature	-55°C
	Forward Voltage Vf	0.8V
	Maximum Operating Temperature	150°C
	Standards/Approvals	No
	Length	2.9mm
	Height	1mm
	Automotive Standard	AEC-Q101

	Sélectionner tout
	Marque Infineon
	Product Type MOSFET
	Channel Type Type N
	Maximum Continuous Drain Current Id 190mA
	Maximum Drain Source Voltage Vds 100V
	Series OptiMOS
	Package Type SOT-23
	Mount Type Surface
	Pin Count 3
	Maximum Drain Source Resistance Rds 10Ω
	Channel Mode Enhancement
	Maximum Power Dissipation Pd 500mW
	Typical Gate Charge Qg @ Vgs 0.6nC
	Minimum Operating Temperature -55°C
	Forward Voltage Vf 0.8V
	Maximum Operating Temperature 150°C
	Standards/Approvals No
	Length 2.9mm
	Height 1mm
	Automotive Standard AEC-Q101

Statut RoHS non applicable

Infineon OptiMOS Series MOSFET, 100V Maximum Drain Source Voltage, 10Ω Maximum Drain Source Resistance - BSS123NH6327XTSA1

This MOSFET is a surface-mount N-channel enhancement transistor designed for switching and control tasks in compact electronic assemblies. It is intended for use across a wide thermal range and in applications where low switching charge and conservative current handling are required. The device is supplied in a SOT-23 package for straightforward PCB mounting and is suitable for environments that demand automotive-grade component robustness.

Features and Benefits:

• 100V drain-source rating enables high-voltage switching capability
• 10Ω Rds(on) simplifies low-power protection and current limiting
• 0.6nC typical gate charge minimises switching losses
• 190mA continuous drain current supports light-load control
• 20V gate voltage rating allows compatibility with common drive levels
• 500mW power dissipation handles modest thermal loads

Applications

• Suitable for battery management sensing circuits
• Ideal for low-current load switching in control modules
• Used with level-shift interfaces in mixed-voltage systems
• Can be used for signal isolation in automotive peripherals
• Appropriate for thermal-limited power distribution networks

What temperature conditions can it withstand in operation?

It operates across a broad range from -55°C up to 150°C, permitting use in both cold-start and high-heat environments.

What mounting and pin configuration does it use?

It is supplied as a three-pin SOT-23 surface-mount package, optimised for automated PCB assembly and small form-factor layouts.

How does its construction influence selection for automotive projects?

The device meets an automotive stress test standard, making it suitable where components must tolerate automotive qualification requirements.

How should thermal dissipation be managed on a PCB?

With a 500mW dissipation limit, designers should provide adequate copper area or thermal vias to spread heat and maintain junction temperatures within safe limits.