Sauter HB0 100-0HB0 100-0. Durometer
- N° de stock RS:
- 136-3545
- Référence fabricant:
- HB0 100-0
- Fabricant:
- Sauter
Sous-total (1 unité)*
157,23 €
(TVA exclue)
190,25 €
(TVA incluse)
Frais de livraison offerts pour toute commande de plus de 75,00 €
En stock
- Plus 2 unité(s) expédiée(s) à partir du 29 décembre 2025
- Plus 7 unité(s) expédiée(s) à partir du 29 décembre 2025
Besoin de plus? Cliquez sur " Vérifier les dates de livraison " pour plus de détails
Unité | Prix par unité |
|---|---|
| 1 + | 157,23 € |
*Prix donné à titre indicatif
- N° de stock RS:
- 136-3545
- Référence fabricant:
- HB0 100-0
- Fabricant:
- Sauter
Spécifications
Documentation technique
Législations et de normes
Détails du produit
Recherchez des produits similaires en sélectionnant un ou plusieurs attributs.
Sélectionner tout | Attribut | Valeur |
|---|---|---|
| Marque | Sauter | |
| Tester Type | Durometer | |
| Shore Scale | Shore A0 | |
| Indenter | Ball Head | |
| Graduation | 1 | |
| Weight | 160g | |
| Dimensions L x W x D | 115 x 60 x 25mm | |
| Sélectionner tout | ||
|---|---|---|
Marque Sauter | ||
Tester Type Durometer | ||
Shore Scale Shore A0 | ||
Indenter Ball Head | ||
Graduation 1 | ||
Weight 160g | ||
Dimensions L x W x D 115 x 60 x 25mm | ||
- Pays d'origine :
- CN
Kern Analogue Shore Hardness Tester
A compact hand held durometer with drag indicator. Ideal for internal comparison measurement. Supplied in a wooden carrying case for safe and secure storage.
Typical Application
• Measurement of penetration (Shore)
Feature and Benefits
• Mechanical shore hardness meter
• For internal comparison measurement. Standard calibrations e.g. to DIN 53505 are often not possible because of narrow standard tolerances
• Shore A: Rubber, elastomers, neoprene, silicone, vinyl, soft plastics, felt, leather and similar material
• Shore D: Plastics, Formica, epoxies, plexi glass etc.
• Shore A0: Foam, sponge etc.
• Max Mode: Holds the maximum value in the display
• Point Mode: Shows one instant value
• Can be attached to test stands SAUTER TI-A0 (for Shore A and A0), TI-D. (for Shore D)
• Tester Shore A0
Parallels, Surface Finish & Hardness
Surface Finish
Any machined component has a surface geometry which consists of three basic elements:
Form or Curvature - Whether the surface has irregular bumps or dimensional changes
Waviness - Whether the surface has regular repetitive ripples or patterns (e.g. milling patterns)
Roughness - The shapes or irregularities that are smaller than, and form part of the waviness pattern (e.g. material micro-structure)
Waviness - Whether the surface has regular repetitive ripples or patterns (e.g. milling patterns)
Roughness - The shapes or irregularities that are smaller than, and form part of the waviness pattern (e.g. material micro-structure)
Waviness and roughness are traditionally the most difficult elements to measure when comparing surface finish, however, they have a radical effect on the performance of the finished component. Variations will cause aesthetic appearance changes, component wear variations, oil retention variation etc. Many manufacturers therefore specify a range of roughness values which their components should be manufactured to, often expressed as: Ra, Rq (RMS), RzDIN, Ry, Sm,mm.