Allegro Microsystems Surface 3.8 V 24V, SOT-23, 3-Pin
- N° de stock RS:
- 177-5548
- Référence fabricant:
- A1104LLHLT-T
- Fabricant:
- Allegro Microsystems
Actuellement indisponible
Nous ne savons pas si cet article sera de nouveau disponible. RS a l'intention de le retirer de son assortiment sous peu.
- N° de stock RS:
- 177-5548
- Référence fabricant:
- A1104LLHLT-T
- Fabricant:
- Allegro Microsystems
Spécifications
Documentation technique
Législations et de normes
Détails du produit
Recherchez des produits similaires en sélectionnant un ou plusieurs attributs.
Sélectionner tout | Attribut | Valeur |
|---|---|---|
| Marque | Allegro Microsystems | |
| Mount Type | Surface | |
| Minimum Supply Voltage | 3.8 V | |
| Maximum Supply Voltage | 24 V | |
| Package Type | SOT-23 | |
| Pin Count | 3 | |
| Automotive Standard | AEC-Q100 | |
| Height | 950 μm | |
| Length | 2.98 mm | |
| Magnetic Type | Unipolar | |
| Maximum Operating Temperature | 150 °C | |
| Minimum Operating Temperature | -40 °C | |
| Response Time | 4 μs | |
| Sensor Type | Hall Effect Sensors, Hall Effect Sensors | |
| Series | A1104 | |
| Standards/Approvals | AEC-Q100 | |
| Supply Current | 7.5 mA | |
| Technology | BiCMOS | |
| Width | 1.91 mm | |
| Sélectionner tout | ||
|---|---|---|
Marque Allegro Microsystems | ||
Mount Type Surface | ||
Minimum Supply Voltage 3.8 V | ||
Maximum Supply Voltage 24 V | ||
Package Type SOT-23 | ||
Pin Count 3 | ||
Automotive Standard AEC-Q100 | ||
Height 950 μm | ||
Length 2.98 mm | ||
Magnetic Type Unipolar | ||
Maximum Operating Temperature 150 °C | ||
Minimum Operating Temperature -40 °C | ||
Response Time 4 μs | ||
Sensor Type Hall Effect Sensors, Hall Effect Sensors | ||
Series A1104 | ||
Standards/Approvals AEC-Q100 | ||
Supply Current 7.5 mA | ||
Technology BiCMOS | ||
Width 1.91 mm | ||
- Pays d'origine :
- GB
A1101/2/3/4/6 Hall Effect Sensor Switch, Allegro Microsystems
The Allegro A1101/2/3/4 and A1106 Hall-effect switches are produced with BiCMOS technology enabling fast power-on time and low-noise operation. Device programming is performed after packaging, to ensure increased switch-point accuracy by eliminating offsets that could be induced by package stress.
Unique Hall element geometries and low offset amplifiers minimise noise and to reduce the residual offset voltage normally caused by device over-molding and thermal stress.
The Allegro A1101/2/3/4 and A1106 a voltage regulator, Hall voltage generator, small-signal amplifier, Schmitt trigger, and NMOS output transistor.
The integrated voltage regulator permits operation from 3.8 V to 24 V and on-board protection circuitry provides a ±30 V absolute maximum voltage rating. All devices in the family are identical except for magnetic switchpoint levels.
Continuous-time operation with fast power-on time and low noise
Stable operation over full operating temperature range
Reverse battery protection
Solid-state reliability
Factory-programmed at end of line for optimum performance
Robust EMC performance
High ESD rating
Regulator stability without a bypass capacitor
Hall Effect Sensors, Allegro MicroSystems
Liens connexes
- Allegro Microsystems Surface Hall Effect Sensor 3.8 V 24V 3-Pin
- Allegro Microsystems 1 Axis Surface Hall Effect Sensor 3.8 V 24V 3-Pin
- Allegro Microsystems Surface Hall Effect Sensor 3 V 24V 3-Pin
- Allegro Microsystems Surface Hall Effect Sensor 4.5 V 5.5V 3-Pin
- Allegro Microsystems Surface Hall Effect Sensor 2.4 V 5.5V 3-Pin
- Allegro Microsystems Surface Hall Effect Sensor 2.5 V 3.5V 3-Pin
- Allegro Microsystems Through Hole Hall Effect Sensor 3.8 V 24V 3-Pin
- Allegro Microsystems 1 Axis Surface Hall Effect Sensor 4.5 V 5.5V SOT-23, 3-Pin
