Time Electronics 7006 Loop Calibrator Battery

Voir la catégorie

Sous-total (1 unité)*

452,00 €

(TVA exclue)

546,92 €

(TVA incluse)

Add to Basket
sélectionner ou taper la quantité
En stock
  • Plus 55 unité(s) expédiée(s) à partir du 09 février 2026
Besoin de plus? Cliquez sur " Vérifier les dates de livraison " pour plus de détails
Unité
Prix par unité
1 +452,00 €

*Prix donné à titre indicatif

N° de stock RS:
537-7658
Référence fabricant:
7006
Fabricant:
Time Electronics
Recherchez des produits similaires en sélectionnant un ou plusieurs attributs.
Sélectionner tout

Marque

Time Electronics

Product Type

Loop Calibrator

Model Number

7006

Accuracy

±0.1 %

Battery Type

PP3

Battery Life

40h

Power Source

Battery

Minimum Operating Temperature

-5°C

Maximum Operating Temperature

50°C

Weight

180g

Width

65 mm

Standards/Approvals

No

Height

140mm

Length

30mm

Hazardous Area Certification

No

Calibrated

UKAS

Statut RoHS : Exempté

Pays d'origine :
GB
Loop-Mate1 generates 4 to 20 mA or 0 to 10V to simulate loop signals. Audible beeps that change pitch in sympathy with the output level plus auto-stepping through the range simplify a calibration engineer’s job. It has several additional features - it can generate the current using its own internal supply (RX Test mode), or control the current using an external supply (TX Sim mode).

TxSim and RxTest

Time Electronics Loop-Mate 1 & 2 Current Loop Calibrator


Loop-mates designed for the calibration, testing and measurement of process loops are pocket sized units that boast a simplistic operation, no complicated selections just grab and go.

Loop-Mate 1 (537-2580) - Simulator which acts as a source in providing loop signals, a simple up and down button allows the user to increase or decrease the signal.

7 set points: 10%, 25%, 50%, 75%, 90% and 100% each of which is shown on LED's with beeps. The Loop-Mate 1 when used in conjunction with Loop-Mate 2 allows users to check a signal has arrived within specification at another location.

Loop-Mate 2 (537-2603) - Signal indicator with a 4-20 mA or 0-10 V loop type selection, also allowing the user to choose between a display of direct units or % of span. Also, specifically designed so that the LCD display shows the signal in mA, V, or % of span within an accuracy of 0.05%.

Powered by a PP3 battery both units provide up to 40 hours of continuous use, making them the ideal addition to any engineer testing kit.

Features and Benefits Loop-Mate 1:


• 0.1% Accuracy

• TxSim or RxTest mode

• 25 mA max loop supply

• 140 x 65 x 30 mm dimensions

Features and Benefits Loop-Mate 2:


• 4-digit LCD display

• 0.05% accuracy

• RxSim, TxTest, 50mA/50V measure

• 140 x 65 x 30 mm dimensions

FAQ's


What is a current loop calibrator?


Current loop calibrators are specially designed instruments for current loop trouble shooting, testing and calibration. They can source current on unpowered devices in a loop, simulate the operation of loop powered transmitters and also measure current. These calibrators often feature time saving technology, specialist graphics using digital interfaces and micro-processor based electronics.

How much current flows in each loop of a parallel circuit?


Determined by Ohm's law, which states that the current between 2 points through a conductor is directly proportionate to the voltage across those 2 points, divided by the resistance of the conductor. I = V/R. This is also the case for series and parallel circuits, however in parallel circuits the total current can be affected by the way the resistors have been connected, as well as their ohmic value. Current does divide up and there can be more current in one area over another nonetheless when all areas are added up the total amount is the same.

Note

Loop-Mate 1 is a simulator
Loop-Mate 2 is an indicator

Supplied with

Carry case, leads and technical manual

Liens connexes