RS PRO Light Transformer 150 W, 230 to 240 V ac, 12 V

N° de stock RS:: 714-1381
Fabricant:: RS PRO

RS PRO Light Transformer 150 W, 230 to 240 V ac, 12 V

Sous-total (1 unité)*

41,79 €

(TVA exclue)

50,57 €

(TVA incluse)

Frais de livraison offerts pour toute commande de plus de 90,00 €

En stock

29 unité(s) prête(s) à être expédiée(s) d'un autre centre de distribution
Plus 25 unité(s) expédiée(s) à partir du 28 août 2026

Besoin de plus? Cliquez sur " Vérifier les dates de livraison " pour plus de détails

Unité	Prix par unité
1 +	41,79 €

*Prix donné à titre indicatif

N° de stock RS:: 714-1381
Fabricant:: RS PRO

Spécifications

Documentation technique

Législations et de normes

Détails du produit

Recherchez des produits similaires en sélectionnant un ou plusieurs attributs.

Sélectionner tout	Attribut	Valeur
	Marque	RS PRO
	Product Type	Light Transformer
	Primary Voltage	230 to 240 V ac
	Secondary Voltage	12 V
	Power	150W
	Minimum Load Requirement	30W
	Maximum Operating Temperature	70°C
	Minimum Operating Temperature	40°C
	Sub Type	Dimmable Electronic Transformer
	Termination Type	Screw
	Mount Type	Screw
	Width	49mm
	Weight	205g
	Length	190mm
	Depth	39mm
	Series	WOLF 150 - WX 150
	Standards/Approvals	EN 61347-2-2, VDE 0710-T14, EN 61347-1, EN 61547, EN 55015, EN 60598-1, EN 61000-3-2
	Dimming Method	Trailing Edge
	Minimum Operating Frequency	50Hz
	Maximum Operating Frequency	60Hz

	Sélectionner tout
	Marque RS PRO
	Product Type Light Transformer
	Primary Voltage 230 to 240 V ac
	Secondary Voltage 12 V
	Power 150W
	Minimum Load Requirement 30W
	Maximum Operating Temperature 70°C
	Minimum Operating Temperature 40°C
	Sub Type Dimmable Electronic Transformer
	Termination Type Screw
	Mount Type Screw
	Width 49mm
	Weight 205g
	Length 190mm
	Depth 39mm
	Series WOLF 150 - WX 150
	Standards/Approvals EN 61347-2-2, VDE 0710-T14, EN 61347-1, EN 61547, EN 55015, EN 60598-1, EN 61000-3-2
	Dimming Method Trailing Edge
	Minimum Operating Frequency 50Hz
	Maximum Operating Frequency 60Hz

Pays d'origine :: IT

RS PRO Dimmable Electronic Transformer

Use this independent transformer in conjunction with 12/ 24 V halogen lamps. This clever device offers protection against electric shock following direct or indirect contact and is dimmable by trailing or leading-edge dimmer. Our electronic transformer come complete with opposite inlet and outlet terminals, terminal cover, and cable retainer.

Features and Benefits

Independent transformer

Dimmable

Terminal cover and cable retainer

Opposite inlet and outlet terminals

Input terminals with loop possibility on feed

Double terminal block on the 230 V primary circuit (2,5 mm2 terminal area)

Triple terminal block on the 12 V secondary circuit (2,5 mm2 terminal area)

Transformer is secured by means of threaded slots

General Specification

Suitable for halogen lamps 12/24 V

Clamping screws on primary and secondary circuits for cables with diameter: 3 mm min. - 8 mm max.

Max 18 mm cable peel-off

Dimensions: 190 mm x 39 mm x 49 mm

Weight: 205 g

IP Rating: IP20

Protection

Protected against overheating and short-circuits

Protected against mains voltage spikes

Protected against overloads

Class II protection

RS PRO

RS PRO is our own brand range and brings you a wide range of high-quality, great value products offering you more choice. Trusted by engineers all over the world, every part of every RS PRO product has been rigorously tested against demanding industry standards they’re only given the RS PRO Seal of Approval if we’re confident of their exceptional quality, which means you can be confident too.

Low Voltage Lighting Transformers

Dimming Methods (where applicable):

Leading Edge:

The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.

Trailing Edge:

Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.