INA HK5022-RS-A-L271 50 mm ID Roller Bearing Drawn Cup Needle, 58 mm OD
- N° de stock RS:
- 194-6953
- Référence fabricant:
- HK5022-RS-A-L271
- Fabricant:
- INA
Offre groupée disponible
Consulter les options de prix de grosSous-total (1 unité)*
25,58 €
(TVA exclue)
30,95 €
(TVA incluse)
Frais de livraison offerts pour toute commande de plus de 90,00 €
En stock
- 1 unité(s) prête(s) à être expédiée(s) d'un autre centre de distribution
Besoin de plus? Cliquez sur " Vérifier les dates de livraison " pour plus de détails
Unité | Prix par unité |
|---|---|
| 1 - 4 | 25,58 € |
| 5 - 9 | 24,10 € |
| 10 - 24 | 23,57 € |
| 25 + | 23,09 € |
*Prix donné à titre indicatif
- N° de stock RS:
- 194-6953
- Référence fabricant:
- HK5022-RS-A-L271
- Fabricant:
- INA
Spécifications
Documentation technique
Législations et de normes
Détails du produit
Recherchez des produits similaires en sélectionnant un ou plusieurs attributs.
Sélectionner tout | Attribut | Valeur |
|---|---|---|
| Marque | INA | |
| Product Type | Roller Bearing | |
| Inside Diameter | 50mm | |
| Race Width | 22mm | |
| Bore Type | Parallel | |
| Cage Material | Steel | |
| Static Load Rating | 63kN | |
| Outside Diameter | 58mm | |
| Standards/Approvals | No | |
| End Type | Sealed | |
| Dynamic Load Rating | 31kN | |
| Bearing Type | Drawn Cup Needle | |
| Sélectionner tout | ||
|---|---|---|
Marque INA | ||
Product Type Roller Bearing | ||
Inside Diameter 50mm | ||
Race Width 22mm | ||
Bore Type Parallel | ||
Cage Material Steel | ||
Static Load Rating 63kN | ||
Outside Diameter 58mm | ||
Standards/Approvals No | ||
End Type Sealed | ||
Dynamic Load Rating 31kN | ||
Bearing Type Drawn Cup Needle | ||
Are particularly suitable for Applications with a very small radial section height on account of their very low cross-sectional height
Are used if the housing bore is not suitable as a raceway for needle roller and cage assemblies
Can support high radial loads (are pure radial bearings)
Require a considerably smaller radial design envelope than machined needle roller bearings
Usually run directly on the shaft (no inner ring)
Permit relatively high speeds
Are easy to mount
Require no additional means of axial retention (as a result of which the housing bore is easy to produce)
Can be readily used to close off the shaft ends of bearing positions (drawn cup needle roller bearings with closed end)
Result in particularly compact, cost-effective and economical bearing arrangements
Liens connexes
- INA HK5024-2RS-A-L271 50 mm ID Roller Bearing Drawn Cup Needle, 58 mm OD
- INA HK2516-2RS-L271 25 mm ID Roller Bearing Drawn Cup Needle, 32 mm OD
- INA HK2520-2RS-L271 25 mm ID Roller Bearing Drawn Cup Needle, 32 mm OD
- INA HK1416-2RS-L271 14 mm ID Roller Bearing Drawn Cup Needle, 20 mm OD
- INA HK1614-RS-L271 16 mm ID Roller Bearing Drawn Cup Needle, 22 mm OD
- INA HK1616-2RS-L271 16 mm ID Roller Bearing Drawn Cup Needle, 22 mm OD
- INA HK3520-2RS-L271 35 mm ID Roller Bearing Drawn Cup Needle, 42 mm OD
- INA HK2018-RS-L271 20 mm ID Roller Bearing Drawn Cup Needle, 26 mm OD